Engineering

Permanent URI for this community

https://repository.elizadeuniversity.edu.ng/handle/20.500.12398/6
These are the scholarly outputs of the Faculty of Engineering

Browse

Browsing Engineering by Author "Abiola, O. A."

Now showing 1 - 3 of 3
  • Thumbnail Image
    Item
    The Effect of Beneficiation on Some Properties of Osun State Ceramic Raw Materials
    (Journal of Casting & Materials Engineering, 2019) Abiola, O. A.; Oke, Adekola Olayinka; Omidiji, Babatunde Victor; Adetan, Dare Aderibigbe
    Clay, feldspar and silica sand are important industrial minerals which often need treatment commonly known as beneficiation to improve the quality of ceramic tiles produced from these materials. The different minerals, after sorting, were treated separately in distilled water, alcohol and hydrochloric acid before being crushed in a ball mill; they were then characterized using a pelletron accelerator. The results show an increased silicon content for clay, silica sand and feldspar; and reduced aluminum content for clay and silica sand but not for feldspar. Iron impurity and its oxide are also shown to reduce by over 50% in all the minerals while potassium was found to be the dominant element in feldspar among the defining elements. In conclusion, the increased quartz in the mineral will improve the hardness, density, porosity, and rigidity of ceramic tiles as well as providing support and controlling shrinkage. Furthermore, increasing the mineral quotient in feldspar will enhance its fluxing potential.
  • Thumbnail Image
    Item
    The Effects of Heat Generation on Cutting Tool and Machined Workpiece
    (Journal of Physics: Conference Series, 2019-07) Ogedengbe, T.S.; Okediji, A. P.; Yussouf, A. A.; Aderoba, O. A.; Abiola, O. A.; Alabi, I. O.; Alonge, O. I
    Metal cutting processes usually cause heat generation at the cutting zone (around the workpiece-tool intersection). The heat generated during these processes may cause different effects on both the workpiece and tool, this in turn may affect the finished product and the general performance of the machined piece. In this study, a review was done on various types of machining conditions available, effects of heat generated on the workpiece and tool, and the approaches adopted to reduce this heat at cutting zones. This study also focuses on the simulation of percentage ratio of heat removal. To handle the simulation, various approaches of heat removal methods were used to get the percentage ratio using the ansys version 19.1 software. It was discovered that heat generation causes two major types of wear on the tool, crater and flank wear, resulting in the reduction of cutting tool life as well as dimensional inaccuracy, surface damage and severe corrosion cases on the workpiece. Various heat reduction methods and coolant application types were as well studied and their merits and demerits were discussed.
  • Thumbnail Image
    Item
    The Effects of Heat Generation on Cutting Tool and Machined Workpiece
    (International Conference on Engineering for Sustainable World, 2019) Ogedengbe, T.S.; Okediji, A. P.; Yussouf, A. A.; Aderoba, O. A.; Abiola, O. A.; Alabi, I. O.; Alonge, O. I.
    Metal cutting processes usually cause heat generation at the cutting zone (around the workpiece-tool intersection). The heat generated during these processes may cause different effects on both the workpiece and tool, this in turn may affect the finished product and the general performance of the machined piece. In this study, a review was done on various types of machining conditions available, effects of heat generated on the workpiece and tool, and the approaches adopted to reduce this heat at cutting zones. This study also focuses on the simulation of percentage ratio of heat removal. To handle the simulation, various approaches of heat removal methods were used to get the percentage ratio using the ansys version 19.1 software. It was discovered that heat generation causes two major types of wear on the tool, crater and flank wear, resulting in the reduction of cutting tool life as well as dimensional inaccuracy, surface damage and severe corrosion cases on the workpiece. Various heat reduction methods and coolant application types were as well studied and their merits and demerits were discussed.