Research Articles in Automotive Engineering
Permanent URI for this collection
Browse
Browsing Research Articles in Automotive Engineering by Subject "Comsol"
Now showing 1 - 3 of 3
Results Per Page
Sort Options
Item Heat Transfer Analysis in Internal Combustion Engine Piston Using Comsol Multiphysics: A Case Study of Tri-Cycle(International Journal of Scientific & Engineering Research, 2016-07-30) Oke, David B.; Alabi, Ismaila O.; Adegbola, Adekunle A.The transient nature of heat flowing involving more than single variable, complicated method of measuring temperature across the length of the liner and ambiguous boundary conditions pose serious problems for the analysis of heat transfer rate on the piston of an internal combustion engine using FEM (Finite Element Method). This present study analyzed the heat transfer rate on the piston of a Tri-cycle engine. The studied piston was selected based on its applications in automobile and other engineering applications. The analysis was basically on the transient state forced-convection and conduction heat transfer. As initial condition, the temperature distributions were considered along the piston at a range of 523K – 673K. The parameter used for the simulation were liquid (Gasoline), Gases (Air) and Aluminium silicon UNSA96061 (Piston). The modeling and simulation were performed by using COMSOL-Multiphysics 4.3a software. The mesh optimization was undertaken by using FEM techniques to predict the maximum and mimimum temperature on the piston at every stages of simulation with time dependent. It was discovered that the temperature along the piston of the try-cycle varies with respect to time. The transient analysis revealed that the temperature of the piston at the TDC (Top Dead Center) in the first power stroke is higher compare to the subsequent power strokes, which is an indication that more heat is transfer at subsequent power strokes. Probable recommendations were later made.Item Numerical Simulation and Modeling of UNSA91060 for Heat Transfer in Four-Stroke ICE Cylinder Head(International Journal of Advanced Engineering, Management and Science (IJAEMS), 2018-03-30) Olaiya, Kamorudeen A.; Alabi, Ismaila O.; Falana, Kafayat A.Heat transfer is one of a number of indispensable tools in studying of ICEs, due to its influence on decisive parameters of operation like temperature and pressure inside the cylinder. It is safe to say that modeling of the engine heat transfer is among the most complex problems for engineers. Application of numerical methods to predict the heat transfer in a cylinder of reciprocating ICEs is a process of high importance, which was recognized from the earliest stages of their development. This is done to examine performance optimization and design improvement in order to meet nowadays demands exhibited on the engines. This present study focuses on a 3-D transient state temperature distribution analysis on a gasoline engine model via formulated of models, simulating using FEM in-built in the COMSOL Multiphysics software 4.3a to determine the temperature distribution and gradient of the engine cylinder head model. The number of degrees of freedom solved for were 32685 in 383 s (12 minutes, 20 seconds) in the mesh optimization. From the result obtained it was discovered that the heat transfer in the combustion chamber of the ICE varies with time. Thus, it took the engine 10 minutes to complete a cycle vis-a-vis transfer of heat after combustion and that the heat transfer starts after 30 seconds of combustion. In addition, the temperature of the cylinder dropped from 1273.2 K to 301 K over a period of 10 minute.Item Numerical Simulation of Temperature Distribution in A Tri-Cycle Engine Piston(International Journal of Scientific & Engineering Research, 2015-06-30) Alabi, Ismaila O.; Olaiya, Kamorudeen A.; Kareem, Mutiu O.Pistons as one of the most complex components among all automotives and other industry field components are designed to withstand damage caused due to extreme heat and pressure of combustion process. Many of experimental studies regarding the internal combustion engines process have been carried out, but few had only focused on the numerical studies like stress distribution, thermal and heat transfer analysis. This present study focuses on a 3-D transient state temperature distribution analysis on a gasoline piston model of a tri-cycle. Mathematical model was formulated, solved and simulated using a Finite Element Method (FEM) in-built in the COMSOL Multiphysics software 4.3a to determine the temperature distribution and gradient of the piston model ranging from 523K – 673K. The parameters used for the simulation were liquid (Gasoline), Gases (Air) and Aluminium alloy UNSA96061 (Piston). The Completed mesh tetrahedral consists of 86225 elements and the number of degrees of freedom solved for were 18553 in 367 s (6 minutes, 7 seconds) in the mesh optimization. It was discovered from the results obtained that the temperature in the combustion chamber of the tricycle engine varies with respect to time, along the piston.The transient analysis from the time dependent solver revealed that the temperature of the piston at the TDC (Top Dead Centre) in the first power stroke is higher compared to the subsequent power strokes, which is an indication that more heat was transfer at subsequent power strokes. Probable recommendations were later made.